Home » Responsive Respiratory Tubing Connector for Oxygen Tubing

Responsive Respiratory Tubing Connector for Oxygen Tubing

Where To Buy?


Find out the relevant products below and buy Responsive Respiratory Tubing Connector for Oxygen Tubing.


Alternative Product Link:


Click Here if you don’t find Responsive Respiratory Tubing Connector for Oxygen Tubing in the above list.

Main Benefits:


Here are a few main benefits of Responsive Respiratory Tubing Connector for Oxygen Tubing.

  • Easy to use for leak-free coupling
  • Male to male
  • Pack 5

Better Alternative:


We found these products are better than Responsive Respiratory Tubing Connector for Oxygen Tubing.

Last update on 2020-09-26 / Affiliate links / Images from Amazon Product Advertising API


More Info:


Here are some more information on Responsive Respiratory Tubing Connector for Oxygen Tubing.
Attaches to all standard tubing and cannulas.**This is a single-use device. For medical hygiene reasons, once sealed polybag has been opened, this product cannot be returned, per Hazardous Materials policy**

Frequently Asked Questions:


Here are a few frequently asked questions and answers on Responsive Respiratory Tubing Connector for Oxygen Tubing.

Question Question 1

What Is The Diameter Of This Tubing Connector?

It is approx. 5 mm at the narrowest part.or abt. 1/8″.it’s not that easy to measure.The opening is the same on both sides and works with standard tubing, unlike the “swivel” type which is very narrow on one end, each opening is equal.It will work w/regular tubing as well as high flow tubing (which is what we use).

Question Question 2

Need To Run Oxygen Tubing Thru A Wall In Our House. Need To Cut The Tubing Because The End Connector Is Too Big To Pass Thru.Would This Patch It?

No – this is meant for use with the standard end of a cannula or supply tubing.It is not designed to work with a cut end of tubing.

Question Question 3

How Many Are In A Pack?

This is for 5 pieces

Question Question 4

Will This Connector Fit Into Standard Oxygen Tubing Or Does It Need To Slide Into A Female Fitting That Was Previously Welded Onto Standard Tubing?

This fits into the standard female oxygen tubing port.It will not fit just the tubing itself if it has been cut.

Question Question 5

All Of Our Dad’S Tubing Is Already Connected To A Cannula. Can We Simply Cut A Tube To Use This Connector?

This connector is used to join tubing to a cannula.It will not fit if you cut the tube, it is designed to fit the end of the cannula as-is.

Question Question 6

Does This Connector Slide Into The “Raw” Hose Or Must The Hose Have That Special Connector On It?

You must have the end connector on the tubing to use these. we bought some hard plastic tubing with an inside diameter that matched the outside diameter of the soft O2 tubing, cut it to about 2-1/2 to 3″ and cleaned these pieces with alcohol and then slide the O2 tubing into the to join the common tubing with the specia You must have the end connector on the tubing to use these. we bought some hard plastic tubing with an inside diameter that matched the outside diameter of the soft O2 tubing, cut it to about 2-1/2 to 3″ and cleaned these pieces with alcohol and then slide the O2 tubing into the to join the common tubing with the special connectors. Because the pressure is very low there is little danger of it coming apart and you can still take it apart.

Question Question 7

A Hose With 5/32″ Inside Diameter Will Fit?

yes but the dimensions will be metric.

Question Question 8

Is There A Short Cannula For Portable Concentrator?

There are 2ft and 4ft cannulas available – not sure if they are available on .


Our Insights:


See our insights (based on our own experience after purchasing and using the product, or based on some research work) on Responsive Respiratory Tubing Connector for Oxygen Tubing, these might be useful for better understanding.

Fine quality and sufficiently strong to withstand the rigors of installation and unprotected exposure. If you intend to use these, be sure to understand that the ends of the tubing to be connected must be heated in very hot water to allow them to distort enough to fit over these barbs.

We had a neb machine which didn’t work with the neb tubing. It kept popping off when the machine was in operation. We ordered soft rubber tubing and connected it to the machine, then the splicer, then the nebulizer tubing. Works like a champ. We only knew to use this method because of our career as a nurse where these little gizmos are used frequently by respiratory therapy. We didn’t even know it was called a splicer. We found it referred as that on other site, whereas here it is called a connector. Whatever. It works.

We used it to extend the length of our nasal tubing.

It is what it is. Some flow restriction.

Nice connector.

So glad to have received them so quickly.

Okay.

Very simple to use works great.

Good tubing at a good price.

Cheap and works well.

Just your standard oxygen tubing connector.

It does the job.

Very nice.

Great product, fair price, fast shipping. What more could you ask?.

Solve the problem for a tubing connection.

As discribed.

Fine.

We like the way they easily go on hose. Cheaper than ordered longer hose from other medical places.

Item is a real blessing. Keeps our oxygen tubing from twisting and kinking. Great item.

It works good. It was inexpensive.

Last update on 2020-09-26 / Affiliate links / Images from Amazon Product Advertising API

Leave a Reply

Your email address will not be published. Required fields are marked *

eighteen + 5 =

Share via
Copy link